Mobile Secret Codes

Nokia N95 Secret Codes

2008-06-08T14:12:00.000-07:00

*#06#
IMEI number (International Mobile Equipment Identity)

*#0000#
Firmware version and date, Phone Model and Operator Variant

*#92702689#
Life timer (W A R 0 A N T Y) - The amount of time your phone has spent sending and receiving calls.

*#62209526#
Wireless MAC Address (M A C _ W L A N)

*#2820#
Bluetooth MAC address (B T A 0?)

*#7370#
Format phone (R E S 0 ?)

*#7780#
Factory Reset (R S T 0 ?)

Note:
Format phone restores phone to as if it was out of the box. Retains firmware version and operator Variant changes but wipes all applications you have installed. Does not format the memory card so any apps on there may reinstall once powered back up again.

Another way to format some symbian phones: Power off phone. Press and hold Green, * and 3 and keep them held whilst powering on and for a few seconds after.

Factory Reset resets all settings to defaults but keeps any applications you have installed and photos etc. Both need the Security code, which, by default, is 12345.

N95 picture viewer:
2 – Scroll up (when zoomed)
4 – Scroll left (when zoomed)
5 – Zoom in (12.5%/25%/50%)
6 – Scroll right (when zoomed)
8 – Scroll down (when zoomed)
0 – Zoom out

Press and hold (in Standby):
Right selection key: Voice commands
Multimedia Key: Now Playing
1: Voicemail
2-9: shortcuts to address book you need to set up first
0: Web
#: Switches between General and Silent modes - not supported by all Operator Variants (when composing messages will switch between character and number input when held down)

12# (etc) in standby will dial the number held in location 12 on your SIM address book.

Nokia N93 Secret Codes

2008-06-08T14:08:00.000-07:00

#06#
to check the IMEI.

*#0000#
To check the firmware version and date.

*#92702689# *#war0anty#
To check the IMEI. The date when it was purchased, and the date when it was repaired.

*4720# (*hra0#)
To activates the Half Rate.

#4720# (#hra0#)
To deactivates Half Rate.

*#3370# (*efr0#)
To activates Enhanced Full Rate.

*#746085685# (*#sim0clock#)
To check the SIM clock status.

*#7220# (*#pca0#)
To activate the GPRS and Packet Common Control Channel(PCCCH) supports.

*#7230# (*#pcd0#)
To deactivate the GPRS and Packet common control channel (PCCCH)supports.

*#7760# (*#ssn0#)
To check the manufacturing serial number.

*#2820# (*#bta0#)
To check the Bluetooth MAC address (Phone must have a built in bluetooth adapter).

*#7370925538# (*#res0wallet#)
Reset the mobile wallet.

Nokia E91 Secret Codes

2008-06-08T14:00:00.000-07:00

*#06# : Display the IMEI.

*#0000# : Display the firmware version and date.

*#bta0# : Display the Bluetooth MAC address.

*#opr0logo# : Clear the operator logo .

*#pca0# : Activate the GPRS PCCCH support.

*#pcd0# : Deactivate the GPRS PCCCH support .

*#res0wallet# : Reset the mobile wallet.

*#sim0clock# : Display the SIM clock status.

*#ssn0# : Display the manufacturing serial number.

*#war0anty# : Display the manufacturing and repair.

*efr0# : Enable EFR encoding.

#efr0# : Disable EFR encoding.

*hra0# : Enable HR encoding.

#hra0# : Disable HR encoding.

#pw+1234567890+n#
Display the SIM lock status:

n = 1: provider lock.
n = 2: network lock.
n = 3: country lock.
n = 4: SIM lock.

SMART TRICK :
- Press the media key to switch between now playing and current view.
- Press and hold the media key to start the Visual Radio (FM Radio.
- In Music Player, if you press the joystick up or down twice the scrolling speed goes to 'Fast' mode.

Call Diverting

2008-06-07T14:40:00.000-07:00

All
To Activate: * * 21 * NUMBER # [SEND]
To Cancel: # # 21 # [SEND]
To Check: * # 21 # [SEND]
No Answer
To Activate: * * 61 * NUMBER # [SEND]
To Cancel: # # 61 # [SEND]
To Check: * # 61 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER # [SEND]
To Cancel: # # 62 # [SEND]
To Check: * # 62 # [SEND]
Busy
To Activate: * * 67 * NUMBER # [SEND]
To Cancel: # # 67 # [SEND]
To Check: * # 67 # [SEND]
To Cancel All Call Forwarding # # 002 # [SEND]

Diverting Data Calls

2008-06-07T14:39:00.000-07:00

All
To Activate: * * 21 * NUMBER * 25 # [SEND]
To Cancel: # # 21 # * 25 [SEND]
To Check Status: * # 21 # * 25 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 25 # [SEND]
To Cancel: # # 61 * 25 # [SEND]
To Check Status: * # 61 # * 25 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 25 # [SEND]
To Cancel: # # 62 # * 25 # [SEND]
To Check Status: * # 62 # * 25 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 25 # [SEND]
To Cancel: # # 67 # * 25 # [SEND]
To Check Status: * # 67 # * 24 # [SEND]

Diverting Fax Calls

2008-06-07T14:38:00.000-07:00

All
To Activate: * * 21 * NUMBER * 13 #[SEND]
To Cancel: # # 21 # * 13 # [SEND]
To Check Status: * # 21 # * 13 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 13 # [SEND]
To Cancel: # # 61 * 13 # [SEND]
To Check Status: * # 61 # * 13 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 13 # [SEND]
To Cancel: # # 62 # * 13 # [SEND]
To Check Status: * # 62 # * 13 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 13 # [SEND]
To Cancel: # # 67 # * 13 # [SEND]
To Check Status: * # 67 # * 13 #[SEND]

Call Barring

2008-06-07T14:36:00.000-07:00

Before you can activate these barring services you will need a barring code from your service provider. Call Barring can not be activated if Call Forwarding diverts are already in use.

All Calls
To Activate: * 330 * BARRING CODE # [SEND]
To Cancel: # 330 * BARRING CODE # [SEND]
To Check: * # 330 # [SEND]
All Outgoing Calls
To Activate: * 333 * BARRING CODE # [SEND]
To Cancel: # 333 * BARRING CODE # [SEND]
To Check: * # 333 # [SEND]
All Incoming Calls
To Activate: * 353 * BARRING CODE # [SEND]
To Cancel: # 353 * BARRING CODE # [SEND]
To Check: * # 353 # [SEND]
All Outgoing Calls
To Activate: * 33 * BARRING CODE# [SEND]
To Cancel: # 33 * BARRING CODE # [SEND]
To Check: * # 33 # [SEND]
All Outgoing International Calls
To Activate: * 331 * BARRING CODE# [SEND]
To Cancel: # 331 * BARRING CODE # [SEND]
To Check: * # 331 # [SEND]
All Outgoing International Calls Except To Home Country
To Activate: * 332 * BARRING CODE# [SEND]
To Cancel: # 332 * BARRING CODE # [SEND]
To Check: * # 332 # [SEND]
All Incoming Calls
To Activate: * 35 * BARRING CODE # [SEND]
To Cancel: # 35 * BARRING CODE # [SEND]
To Check: * # 35 # [SEND]
All Incoming Calls When Outside Home Country
To Activate: * 351 * BARRING CODE # [SEND]
To Cancel: # 351 * BARRING CODE # [SEND]
To Check: * # 351 # [SEND]
Canceling All Call Barring # 330 * BARRING CODE # [SEND]

Call Waiting

2008-06-07T14:35:00.000-07:00

To Activate: * 43 # [SEND]

To Deactivate: # 43 # [SEND]

To Check: * # 43 # [SEND]

Calling Line Identity

2008-06-07T14:34:00.000-07:00

Outgoing
To Activate: * 31 # [SEND]
To Deactivate: # 31 # [SEND]
To Check: * # 31 # [SEND]
Incoming
To Activate: * 30 # [SEND]
To Deactivate: # 30 # [SEND]

Trium MTD30

2008-06-07T14:33:00.000-07:00

Monitor mode
Hold C and press 379

Secret menu
Hold C and press 987

Version number
Hold C and press 597

Phase1 and 2
Hold C and press 499

Warm start
Hold C and press 179

Instant turn off
Hold C and press 999

Unlock menu
Hold C and press 787090

Handspring TREO

2008-06-07T14:31:00.000-07:00

1. Open the flip and press the PHONEBOOK button one time to display the dial pad
2. Enter ## and the OTKSL using the numbers on the Dial Pad
3. Press the handset button shown in the diagram above
4. At the Activations screen enter the MIN in the phone number field using the numbers on the device keyboard
5. Put a check in the Enable Number Portability box and type the MSID in the MSIN field
6. Press OK
7. The device will display the network search pop-up and return to the Phonebook display

Toshiba 2032P

2008-06-07T14:29:00.000-07:00

1. Slide the Radio Standby Switch on the left side of the device to the upper side (ON) to activate the phone function. This is the switch with the phone icon over it

2. After power up is completed use the stylus to tap on the ADMIN pull up menu at the bottom of the screen and select ACTIVATION WIZARD. If your device has not yet been activated the ACTIVATION WIZARD will automatically start when you turn on the radio in your device.

3. Tap NEXT 3 times. If the device has been previously activated it will require only 2 presses.

4. On the fourth screen enter the 6 digit OTKSL using keyboard

5. Enter the MIN in both entery fields then tap NEXT

6. Wait for the device to initialize and display “ready to connect”

7. To initiate IOTA tap the word ADMIN at the bottom of the display and then Data Provisioning

8. Programming is complete

Sony Ericsson T10

2008-06-07T14:28:00.000-07:00

*#06#
for checking the IMEI (International Mobile Equipment Identity)

>*<<*<* for checking the firmware revision information (software release) >*<<*<*>>
n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

Shortcut for Last Dialed call menu
If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key
stroke instead: First '0' then '#'.

Access menu without Sim card

To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and you´ll have to take your battery out to turn the phone on again. And this will not care about Phone lock !

A way to (un)lock your cell phone on to the network(subset):
1. Press <**<
2. Then on the display appear and give you two choices: Lock to Network ? and Lock to Network subset? (Use arrow keys to select)
3. Enter the NCK number (code is provided by the SP)
4. You have 5 attemps to do this
5. Then your cell phone will work 'only' with the network

Warning: The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.

Message Report
When you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Sony Ericsson T18

2008-06-07T14:25:00.000-07:00

*#06#
for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:
XXXXXX XX XXXXXX X

TAC FAC SNR SP
TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare
To access SIM-Locking menu of your phone, press: < * [CLR] <
Be careful or you may lock your phone.

Message Report
When you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Sony Ericsson T28

2008-06-07T14:24:00.000-07:00

*#06#
for checking the IMEI (International Mobile Equipment Identity)

>*<<*<* for checking the firmware revision information (software release) >*<<*<*>
1-row text strings. if pressing yes you can check the phones text programming in currently selected language.

>*<<*<*>>
n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

The Service Provider (SP) Lock
The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM car from the same operator.
To activate/deactivate this lock one needs a special secret code that is not available to the end user.

Here is how to activate the menu:
<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.
<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.
Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.

Shortcut for Last Dialed call menu
If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key
stroke instead: First '0' then '#'.

Message Report
When you are writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Samsung T100

2008-06-07T14:23:00.001-07:00

*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also change IMEI to 447967-89-400044-0, you must use CHGIMEI to restore it)

*2767*2878# -> Custom EEEPROM Reset
*#8999*228# -> Battery status (capacity, voltage, temperature)
*#8999*246# -> Program status
*#8999*289# -> Change Alarm Buzzer Frequency
*#8999*324# -> Debug screens
*#8999*364# -> Watchdog
*#8999*377# -> EEPROM Error Stack
*#8999*427# -> Trace Watchdog
*#8999*523# -> Change LCD contrast
*#8999*544# -> Jig detect
*#8999*636# -> Memory status
*#8999*746# -> SIM File Size
*#8999*778# -> SIM Service Table
*#8999*785# -> RTK (Run Time Kernel) errors
*#8999*786# -> Run, Last UP, Last DOWN
*#8999*837# -> Software Version
*#8999*842# -> Test Vibrator
*#8999*862# -> Vocoder Reg
*#8999*872# -> Diag
*#8999*947# -> Reset On Fatal Error
*#8999*999# -> Last/Chk
*#8999*9266# -> Yann debug screen (=Debug Screens?)
*#8999*9999# -> Software version

Samsung V200

2008-06-07T14:22:00.002-07:00

v200 Unlock Code-> *2767*7822573738#
*#9324# Netmon (press the hangup key to exit)
*#9998*JAVA# Edit GPRS/ CSD settings (S100 Only)
*#9998*Help# Help screen/ List of codes
*#9998*LOGO# Change operator Logo
*#9998*RTC# RTC Display
*#9998*Bat# Battery Status
*#9998*Buz# Turns Buzzer ON
*#9998*Vib# Turns Vibrator ON
*#9998*LCD# LCD Contrast
*#9998*9999# Softwre Version
*#9998*8888# Hardware Version
*#9998*377# NVM Error Log (?????)
*#9998*NET# SIM Network ID
*#9998*778# SIM Serv. Table
*#9998*SIM# SIM Info
*#9998*PN# Production No.
*#9998*968# Reminder Tune
*#9998*NVM# Displays Non-Volitile Memory Status
*#9999*C# ???????????????????
*#06# Displays phones I**I No.
***/// ***/// NOTE /// *** RED COLOR , they appear serious !!! Use at
own risk !!!
*#9998*2576# Forces SIM Error
*#9998*DEAD# Forces Phone Crash
*2767*MEDIA# Resets the medis on the phone (deletes all downloaded
pics/tones)
*2767*FULL# Resets the EEPRON *DANGEROUS*
*2767*CUST# Resets the Custom EEPRON
*2767*JAVA# Resets JAV downloads (deletes all downloaded midlits)
*2767*STACKRESET# Resets Stack
*2767*225RESET# ????????????????? * Dangerous *
*2767*WAP# Resets WAP Setting & Deletes Favorites

Samsung A500

2008-06-07T14:22:00.001-07:00

1. Enter ## and the 6 digit OTKSL
2. SERVICE MENU will appear and 1.Basic will be highlighted
3. Press OK
4. Device will display NAM CDMA/ Phone Number
5. Enter 10 digit MIN
6. Press OK (3 times)
7. Display will return to Service Menu. Press END.
8. Programming is complete

Samsung N240 and N400

2008-06-07T14:19:00.000-07:00

Samsung N240 and N400
1. Enter ## and type in the 6 digit OTKSL
2. The display will show SVC MENU and 1. Phone Number
3. Press OK
4. Enter the 10 digit MIN and press OK
5. The display will show NAM with Home SID on the second line (Note: SID is no longer used)
6. Press OK
7. The display will return to the SVC MENU
8. Press END to complete the programming

Sagem MC959 Secret Codes

2008-06-07T14:18:00.000-07:00

In main menu press * for hot-menu:
lcd, led, vibra, tests, imei, software versions, battery voltage

Type MENU - 5 - 1 - 1 - # to enter Engineering menu on SAGEM (RC-712, 721, 815 and 815 plus) phones

Sagem RC815 Pro

2008-06-07T14:17:00.000-07:00

*# Commands
*#06# IMEI number
*#30# followed by send - Corresp. ID incoming displayed
*#31# followed by send - Your ID. outgoing displayed
*#33# followed by send - Call barr inactive
*#35# followed by send - Call barr inactive
*#43# followed by send - Call Waiting
*#100# followed by send - Your mobile number
*#101# followed by send - DHLRU1 ?meaning?
*#102# followed by send - Transmitter information
*#103# followed by send - Current date and time
*#147# followed by send - Last caller's number
*#1345# followed by send - Call credit and service time left

Hidden menu
Engage one of the menus with the scroller then press *
Appli menu: option 1 Version, option 1 Battery
Prom menu: option 1 IMEI number
Sim lock: option 1 Sim lock - press okay for 30 second countdown, C button to cancel (caution with this I don't know what happens when the counter reaches 0!!, it may lock up your telephone's SIM card.
Network: option 1 Option not available
Test LCD: option 1 Symbol 1 Tests screen, option 2 Symbol 2 Tests screen, option 3 Black Tests screen, option 4 For photo Tests screen, option 5 Tests the vibrator

Sagem RC712

2008-06-07T14:16:00.000-07:00

Enter Engineering menu
MENU - 5 - 1 - 1 - #
1) IMEI
2) Flash Eprom etc.
3) ?
4) SP unblock
5) ?
6) Contrast Settings.
When in menu type * and a new menu with new options will appear.

Qualcomm

2008-06-07T14:15:00.000-07:00

QCP-800 programming: menu + 3 + 0.
SPC: "000000" or may be other SPC typed by user.
QCP-820/1920/2035: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.
QCP 1960 and 2760
1. Press softkey under the work MENU
2. Press 8 0
3. Enter the OTKSL
4. Press softkey for OK
5. Enter MIN and press softkey for OK
6. No SID is require for this handset
7. Press softkey for EXIT
8. Programming is complete

Philips C12

2008-06-07T14:06:00.000-07:00

To send free SMS messages on a Philips C12. Type the message and choose to send. As the requesting text comes up hold down the power button and the message will be sent for free!

Secret Codes

*#06# for checking the IMEI (International Mobile Equipment Identity)

If you Put *#06# in the phone and leave it on for 24 hours you will get 50 pounds worth of credit. Works in UK.

To send free SMS messages on a Philips C12. Type the message and choose to send. As the requesting text comes up hold down the power button and the message will be sent for free!

Or you can send free SMS if you have no more talktime.

Phonebook Position
xx# - xx position in Phone Book (e.g. 09#, the number is saved on place 09)

Philips Diga

2008-06-07T14:05:00.000-07:00

Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#

Service Provider Lock

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Philip Fizz

2008-06-07T14:04:00.000-07:00

IMEI code *#06#
SW info *#8377*#
Security code *#1234*#

Service Provider Lock

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Pin Outs
1. GROUND
2. GROUND
3. HANDS FREE ON/OFF
4. MUTE
5. TX
6. RX
7. RTS
8. REPROGRAMMING
9. ON HOOK CHARGER (APPROX 13V? TO 14V)
10. AUX MIC
11. AUX SPEAKER
12. GROUND

Philips Genie

2008-06-07T14:02:00.000-07:00

*#06#
IMEI number (International Mobile Equipment Identity)

*#2254*#
Status register: C, BS, RR, MMI, CREAT.

*#2255*#
activate and deactivate the "DEBUG CALL"-Mode; when activated, make a call to a busy line an the phone will disp some hex-codes on the disp.

*#2558*#
the time in days,hours and minutes you are connected to the net

*#2562*#
not clear; the phone reconnects to the net

*#2565*#
not clear; warmstart ?

*#3333*#
NO) BLOCKING - list (15 items)

*#2377*#
"BEER": not clear, the phone waits a random time and reconnects to the net, sometimes the phone makes a reset or something

*#3377*#
Init, Flags, SIM LCK

*#3353*#
resets the (NO) BLOCKING - list

*#7378*#
Name, Length, SIM phase

*#7489*#
SECURITY CODE

*#7693*#
you can activate and deactivate the SLEEP MODE (when deactivated the battery will go down!)

*#7787*#
not clear: SPURIOUS INTERRUPT

*#7948*#
SWITCH OFF: not clear; it is a timer or something

*#8463*#
Some information about the SLEEP MODE: Wake, Sleep Req., Sleep

Philips Genie (TCD838)

2008-06-07T14:01:00.000-07:00

Type *#2337*# and it will be activate the beep signal when the cellphone reconnected to the net.

Service Provider Lock

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Philips Spark

2008-06-07T14:00:00.000-07:00

MEI code *#06#

Service Provider Lock

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Pin Outs

1. GROUND
2. GROUND
3. HANDS FREE ON/OFF
4. MUTE
5. TX
6. RX
7. RTS
8. REPROGRAMMING
9. ON HOOK CHARGER (APPROX 13V? TO 14V)
10. AUX MIC
11. AUX SPEAKER
12. GROUND

Panasonic GD 500

2008-06-07T13:59:00.000-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Tips and Tricks
Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

(Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers.

Panasonic GD 600

2008-06-07T13:58:00.000-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.
Tips and Tricks

Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

(Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers

Panasonic GD 30

2008-06-07T13:57:00.002-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.
Tips and Tricks

Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers.

Panasonic GD 250

2008-06-07T13:57:00.001-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.
Tips and Tricks

Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

(Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers

Panasonic GD 450

2008-06-07T13:56:00.001-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information
The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

Tips and Tricks
Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

(Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers.

Panasonic GD 520

2008-06-07T13:55:00.000-07:00

To View IMEI (International Mobile Equipment Identity) enter *#06#

Unlock information

The Service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, and one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.
Tips and Tricks

Some service number (SMSC) for sending sms can be found around the world.
We have collected some of them and listed them for you:

Denmark: +4528187000

Only Danish Sonofon subscriber can use this number and only from monday-friday)

Germany: +491722271042
Russia: +78129600096
Unknown: +352091000030
Unknown: +352021100003
Sweden: +46707990001 Comviq
Austrlia +61411990001 Optus

Tip for some service providers:
- Type *n# in the begining of the sms for a status report.
- Type *h# in the begining of the sms to hide your ID.

It seem that TELENOR MOBIL send out letters with the purpose of closing all free servers.

Neopoint 1000

2008-06-07T13:54:00.000-07:00

1. Press M to display Main Menu
2. Scroll to PREFERENCES
3. Press softkey under SELECT
4. Enter 040793
5. Scroll to PROGRAMMING
6. Press softkey under SELECT
7. Enter OTKSL
8. Press softkey under DONE
9. Scroll to PHONE NUMBER
10. Enter 10 digit MIN
11. Scroll to HOME SID
12. Enter SID (4654)
13. Press softkey under SAVE to exit
14. Programming is complete

NEOPOINT 1600

2008-06-07T13:53:00.002-07:00

1. Power the phone on
2. Press the "Menu" key
3. Scroll to "Preferences" - press "Select"
4. Key in the "Field Service Code" (the phone will not prompt you for the code)
at the "preferences" screen to access the "Service" menu (Default code is "000000")
5. Scroll to "Programming" - press "Select" - the phone will ask for the "Subsidy Lock Code"
6. Enter the "Subsidy Lock Code(654321)" to access the "NAM" menu
7. Select the NAM to be programmed (NAM 1 or NAM 2)
8. Program the NAM - Phone number and CDMA Home SID
9. After programming has been completed press "Save" - the phone will reset

NEC N343 Secret Codes

2008-06-07T13:53:00.001-07:00

IMEI 356790000893327
UnlockLock Codes
Code for NCKKN is 0001217819382#
Code for NSCKN is 0002215671182#
Code for SPCKS is 0003217819982#
Code for CKCCK is 0004217611182#
Code for PCKKP is 0005217899382#

Phone Code ResetRepair
Code for NCKKN2 is 0001379889721#
Code for NSCKN2 is 0002379847701#
Code for SPCKS2 is 0003379829721#
Code for CKCCK2 is 0004379841741#
Code for PCKKP2 is 0005379889721#

NEC DB2000 Secret Codes

2008-06-07T13:52:00.000-07:00

See IMEI code
*#06#

Reset to defaults
*73738#

Show Software version
*#2820#

SP Lock info
The procedure will show if your phone is locked.
*#3210# for SIM lock info,
*#8140# for Net lock info.

SIM lock
*#4960 # - Inquiry * 4960 * password * password # (send?) to Lock
#4960* password # to Unlock
[password] is an 8 digits number

Net Lock
*#7320# - Inquiry * 7320 * password * password # to Lock.
#7320* password # to Unlock.
[password] is an 8 digits number

Net Lock 2
*#2220# - Inquiry * 2220 * password * password # to Lock
#2220* password # to Unlock
[password] is an 8 digits number

Subnet Lock
*#1110# - Inquiry * 1110 * password * password # to Lock
#1110* password # to Unlock
[password] is an 8 digits number

Motorola V3688

2008-06-07T13:49:00.000-07:00

*#06# for checking the IMEI (International Mobile Equipment Identity)

Enhanced Full Rate Codec (EFR):

To Enable EFR press [][][] 119 [] 1 [] OK.
To Disable EFR press [][][] 119 [] 0 [] OK

NOTE: Nothing appears on Screen

Motorola 7760, 7860, 2260, 8160

2008-06-07T13:48:00.000-07:00

Nam Programming:

Nam Set: Fcn,0000000000000, Rcl

Nam Set: 74663#, Fcn, Fcn

Test Mode: Fcn, 00**83786633, Sto

Motorola v60c, v120c etc Nam Programming:

Nam Set: 74663#, Menu, Menu, Spc

Nam Set: Menu, 073887, * (type quickly)

Test Mode: Menu, 073887*, Spc

Debug Mode: ##33284

Force the phone into DIGITAL ONLY mode:

1) ##33284 (Debug)

2) RIGHT Softkey (Next) Twice

3) Down arrow 10 times to “PrefMod”

4) RIGHT Softkey (Change) until you see “DigOnly”

5) LEFT softkey (Exit)

6) MENU then LEFT Softkey return to idle screen

7) ##33284 (The last 4 will not display if you have done it correctly)

Motorola t182, c210

2008-06-07T13:47:00.000-07:00

Nam Programming:

Nam Set: ##1111 end

Nam Set: ##298645665 end

Short Nam: ##073887 sto

Motorola v710, v730, v740, ms150, etc Nam Programming:

Nam Set: 8378*# + press 3 times NATE (spc - 071082)

Test Mode: Menu, 073887*, Spc

Service Menu: #758353266#646#

Motorola StarTac 2004 Nam Programming:

Nam Set: 5759789*#, rec key (3)times (spc - 915037)

Motorola ms200, ms230, etc Nam Programming:

Nam Set: 5759789*# (spc - 915037)

Motorola v6060 Nam Programming:

Nam Set:147*369#456*0#

Motorola v60, c120, c331

2008-06-07T13:45:00.002-07:00

1) Turn on the phone. Press MENU 0 7 3 8 8 7 *

2) The phone will require you to “Enter a Security Code”, press 000000, OK

3) Scroll down to “Test mode” choose SELECT. Scroll down to “Enable”
choose SELECT. Your phone is now in test mode.

4) Signal strength is the 3_rd number down on the left hand side of the screen.

5) To toggle between regular mode and test mode: Press MODE then
quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.

6) To turn off the test mode the phone must be in regular mode, then follow
the above sequence and scroll down to where it says “DISABLE” instead of “ENABLE” and choose select.

Mitsubishi MT- D30 Secret Codes

2008-06-07T13:45:00.001-07:00

Monitor mode:
Hold C and press 379

Secret menu:
Hold C and press 987

Version number:
Hold C and press 597

Phase1 and 2 :
Hold C and press 499

Warm start :
Hold C and press 179

Instant turn off:
Hold C and press 999

Unlock menu:
Hold C and press 787090

Mitsubishi Trium Secret Codes

2008-06-07T13:43:00.002-07:00

*#0000#

to reset the phones menu-language to natural language, set initially by the distributor.

*#06#

for checking the IMEI (International Mobile Equipment Identity)

hold * then 5806 - show software version
hold * then 5807 - a littel bit diffrent
hold * then 5472 - Testmode for datacable (it seems so)
hold * then 4329 - Activate and deactivate NETMONITOR
hold * then 621342 - Activate and deactivate another NETMONITOR
hold * then 3926 - shutdown

SP lock
You can turn around the lock routin by entering **04*PIN*PIN*PIN# now
the secretcode change was applied and the software turns back to main
menue. It works not on all triums, only on thos with older sofware
versions.

Kyocera 2345 / 1135

2008-06-07T13:43:00.001-07:00

1. Press 111111 (#1 key 6 times)
2. Option will be highlighted
3. Press OK
4. Scroll down to Programming
5. The service programming dialog will appear Enter Security Code.
6. Enter the 6 digit OTSKL (code will show as asterisks on screen)
7. Service Options will appear
8. Scroll down to the BASIC NAM1 Info
9. Press OK
10. Select the Phone Number by pressing the OK key
11. Using the keypad enter the 10 digit MIN
12. Press OK
13. Press END to complete the programming

Kyocera 6035

2008-06-07T13:41:00.000-07:00

1. Press 1 six times (111111) and select OPTIONS
2. Select PROGRAMMING
3. Open flip
4. Tap the OTKSL on keypad on the screen. Tap OK
5. Tap on the PHONE NUMBER field. Enter MIN.
6. Leave A-KEY blank
7. Enter HOME SID (4654)
8. Tap SAVE & EXIT
9. Tap YES
10. Phone will be in OFF MODE Close flip

Kyocera 3035

2008-06-07T13:40:00.001-07:00

1. Press 111111 (the #1 key six times)
2. Options will be highlighted
3. Press in the navigation key (Navigation key is the button located between the TALK & END key)
4. Scroll to PROGRAMMING using the Navigation key
5. Select PROGRAMMING by pressing in the Navigation key
6. Enter the six digit OTKSL and press in the navigation key
7. SERVICE OPTIONS will appear
8. Scroll down to the Basic NAM1 info
9. Press in the navigation key
10. Clear any numbers that may appear using the “clear” key (arrow key located directly below the navigation key)
11. Select the PHONE NUMBER by pressing in the navigation key
12. Enter the 10 digit MIN select OK by pressing in the navigation key
13. Press END. Programming is complete

Kyocera 2255

2008-06-07T13:39:00.000-07:00

1. Press the 1 key six times (111111) “Option will be highlighted
2. Press OK
3. Scroll down to “Programming” and press “OK”
4. Enter OTKSL and press the navigation key
5. “Service Options” will appear scroll down to the “Basic NAM1 Info”
6. Press OK
7. Select Phone Number by pressing OK
8. Enter MIN and press OK again
9. Scroll to Home SID and press OK
10. Enter SID (4654) and press OK
11. Press END. Programming is complete.

Hitachi P300 Secret Codes

2008-06-07T13:38:00.000-07:00

1. Enter ## and the 6 digit OTKSL
2. Press the Options soft key and then scroll to Save Phone #. Press the OK soft key.
3. At the NAM display scroll to EDIT and press the OK soft key
4. Display will read NAM and MDN will be highlighted. Press the OK soft key.
5. At the MDN display enter the 10 digit MIN and press the SAVE soft key.
6. At the Save prompt press the OK soft key. The next display will show several options that should not edited.
7. Press the EXIT soft key and the device will power cycle.
8. Programming is complete

Hagenuk

2008-06-07T13:37:00.001-07:00

IMEI number:
* # 0 6 #

Software version:
# # 9 1 4 0 * 8 3 # 7 5 * 2 #

Universal Dancall Secret Codes

2008-06-07T13:34:00.002-07:00

IMEI number:
* # 0 6 #

Software version:
* # 9 9 9 9 #

SIMcard serial number:
* # 9 9 9 4 #

Information about battery status:
* # 9 9 9 0 #

Selftest (only Dancall HP2731):
* # 9 9 9 7 #

Show version configuration:
* # 9 9 9 8 #

Net Monitor:
* # 9 9 9 3 #

Bosch 908 Secret Codes

2008-06-07T13:34:00.001-07:00

*#3262255*8378# (*#DANCALL*TEST#) to make secret Engineering menu
(menu 10) appear.

10. Engineering
10.1 MS Info
10.1.1 on
10.1.2 off
10.2 Software details
10.2.1 Software version
10.2.2 EEPROM version
10.2 Test / Production details
10.3.1 Hardware data
10.3.2 Production data
10.3.3 Service data
10.3.4 Mechanical data

*#06# to display the IMEI (International Mobile Equipment Identity)
*#0000# to set the language automaticaly (Reset to english)
*#3370# to set the Enhaced Full Rate
#3370# to Reset the phone
*#9000# to enter sim lock code
*#9001# To enter the corporate code (Bosch 908)
*#9002# To enter the provider code (Bosch 908)
*#9003# to enter the network code
*#9004# to enter the subset code
*#9100# to remove the sim lock permanently
*#9101# to remove the corporate lock permanently
*#9102# to remove the provider lock permanently
*#9103# to remove the network lock permanently
*#9104# to remove the subset lock permanently

(SIM-lock is NOT the SP-lock/Service Provider lock!!)

The SIM-lock makes your phone to fusion with the SIM-card, and
the phone will not accept any other SIM cards after you lock your
phone! You get ten chances to type the correct code! After the
tenth time your phone gets "SIM-lock permanently blocked", and
you will be unable to open it !! The best thing you can do is
to remove the SIM-lock permanently!!

Bosch 909 / 909s Secret Codes

2008-06-07T13:33:00.001-07:00

*#06# to display the IMEI (International Mobile Equipment Identity)
*#0000# to set the language automaticaly (Reset to english)
*#3370# to set the Enhaced Full Rate
#3370# to Reset the phone
*#9000# to enter sim lock code
*#9001# To enter the corporate code (Bosch 908)
*#9002# To enter the provider code (Bosch 908)
*#9003# to enter the network code
*#9004# to enter the subset code
*#9100# to remove the sim lock permanently
*#9101# to remove the corporate lock permanently
*#9102# to remove the provider lock permanently
*#9103# to remove the network lock permanently
*#9104# to remove the subset lock permanently
*#3262255*8378# (*#DANCALL*TEST#) and you will get a hidden 10th menu.

(SIM-lock is NOT the SP-lock/Service Provider lock!!)

The SIM-lock makes your phone to fusion with the SIM-card,
and the phone will not accept any other SIM cards after you
lock your phone! You get ten chances to type the correct code!
After the tenth time your phone gets "SIM-lock permanently blocked"
, and you will be unable to open it !! The best thing you can do
is to remove the SIM-lock permanently!!

Bosch 718

2008-06-07T13:32:00.001-07:00

Secret Engineering menu (menu 10) appear
*#3262255*8378#

Display the IMEI
*#06#

To set the language automatically (Reset to English)
*#0000#

Set the Enhaced Full Rate
*#3370#

Reset the phone
#3370#

Enter sim lock code
*#9000#

Enter the network code
*#9003#

Enter the subset code
*#9004#

Remove the sim lock permanently
*#9100#

Remove the corporate lock permanently
*#9101#

Remove the provider lock permanently
*#9102#

Remove the network lock permanently
*#9103#

Remove the subset lock permanently
*#9104#

Bosch 738

2008-06-07T13:31:00.000-07:00

Bosch COM607

2008-06-07T13:30:00.000-07:00

Bosch 908

2008-06-07T13:29:00.000-07:00

Audiovox 9100

2008-06-07T13:28:00.000-07:00

1. Press ##
2. Enter the OTKSL
3. Display will read Service/Menu 1 Basic…press OK
4. Next screen will read Service Mode/Home SID…press OK
5. Next screen will read Service Mode/Home SID…press OK
6. Device will display Service Menu 1. Basic #
7. Press END button to complete programming

Alcatel HC 600 / 800 / 1000 Secret Codes

2008-06-07T13:27:00.001-07:00

*#06# returns IMEI number and Software Version (not HC600).
These are the pinouts for the HC600 they are the same as the 800/1000 I beleive.
1 3 5 7 9 11 13 15
I I I I I I I I
O O 17
I I I I I I I I
2 4 6 8 10 12 14 16

1 Vbat_ext 9 SDA_E
2 EMMI_PAE 10 GND
3 Mic 11 GND
4 EMMI_OPE 12 DC_IN (charge)
5 GND 13 Speaker
6 EXT_EMET 14 MARCHE
7 SCL_E 15 DC_IN (charge)
8 EXT_RECDIT 16 GND
17 Antenna+internal switch (int/ext)

Alcatel HC400 / HC1000 Secret Codes

2008-06-07T13:26:00.000-07:00

Software releases
HC400 on the backside near the IMEI number is a sticker with a software
release.

Alcatel have split the software releases

1.x No Cellbroadcast
5.x Cell broadcast

The newest software release of the HC 1000 is AK1 03

Alcatel HC 600 / 800 / 1000 Secret Codes

2008-06-07T13:25:00.000-07:00

*#06# returns IMEI number and Software Version (not HC600).

These are the pinouts for the HC600 they are the same as the
800/1000 I beleive.

1 3 5 7 9 11 13 15

I I I I I I I I

O O 17

I I I I I I I I

2 4 6 8 10 12 14 16

1 Vbat_ext 9 SDA_E
2 EMMI_PAE 10 GND
3 Mic 11 GND
4 EMMI_OPE 12 DC_IN (charge)
5 GND 13 Speaker
6 EXT_EMET 14 MARCHE
7 SCL_E 15 DC_IN (charge)
8 EXT_RECDIT 16 GND
17 Antenna+internal switch (int/ext)

Alcatel One Touch Easy

2008-06-07T13:24:00.000-07:00

To view IMEI (International Mobile Equipment Identity) number enter
*#06#

To Enter Service Menu enter: *#000000#

To view Secret Menu type 000000 then press *

Secret Menu Appears
TRACES channel indicator menus
ARRETS - ?
VIDER ARRETS Press OK and the phone responds: This action is executed!
CTRL CHARGE It show the charger voltage and battery voltage.
DAMIER display test

The Service provider (SP) lock is used to lock the cell phone to the
SP's SIM card. Once the cell phone is locked to a specific operator,
if one inserts a SIM card from a different operator the phone will
refuse to accept it! The cell phone will however accept another SIM
card from the same operator.

Removing SP lock on Alcatel Easy
This is how to remove the SP lock on Alcatel (one touch) Easy.
(You wil need a cable, a eeprom device and some sw)

Edit the eeprom:

Address Replace with
------------- ---------------
176h FFh
177h FFh

Siemens S25, M35, S35, C35

2008-06-05T14:36:00.000-07:00

*#0003*(secret code 8 digits)#
SP unlock

*#0606#
shows you Secret Code, but only without SIM Card.

*#06#
for checking the IMEI (International Mobile Equipment Identity)

* # 0000 # then Green button
Resets language to automatic selection

Universal Secret Codes LG Phone

2008-06-05T14:27:00.000-07:00

LG all models test mode: Type 2945#*# on the main screen.

2945*#01*# Secret menu for LG

IMEI (ALL): *#06#

IMEI and SW (LG 510): *#07#

Software version (LG B1200): *8375#

Recount cheksum (LG B1200): *6861#

Factory test (B1200): #PWR 668

Simlock menu (LG B1200): 1945#*5101#

Simlock menu (LG 510W, 5200): 2945#*5101#

Simlock menu (LG 7020, 7010): 2945#*70001#

Simlock menu (LG 500, 600): 2947#*

LG-U81XX SPECIAL CODES

Code to read phone version :

- Phone without SIM

- Enter 277634#*# or 47328545454#

- Select 'SW Ver.info'

Code to reset phone :

- Phone without SIM

- Enter 277634#*# or 47328545454#

- Select 'Factory Reset'

Code to enter UNLOCK MENU :

- Phone wit SIM inside

- Enter 2945#*88110#

Test Menu 8330 : 637664#*#

Test Menu 8180 V10a: 49857465454#

Test Menu 8180 V11a: 492662464663#

Test Menu 8130-8138: 47328545454#

Test Menu 8110-8120: 277634#*#

Universal Samung Secret Codes

2008-06-05T14:21:00.000-07:00

*#06#
Show IMEI

*#9999#
Show Software Version

*#0837#
Show Software Version (instructions)

*#0001#
Show Serial Parameters

*#9125#
Activates the smiley when charging.

*#9998*228#
Battery status (capacity, voltage, temperature)

*#9998*246#
Program status

*#9998*289#
Change Alarm Buzzer Frequency

*#9998*324#
Debug screens

*#9998*364#
Watchdog

*#9998*377#
EEPROM Error Stack - Use side keys to select values. Cancel and ok.

*#9998*427#
Trace Watchdog

*#9998*523#
Change LCD contrast - Only with version G60RL01W

*#9998*544#
Jig detect

*#9998*636#
Memory status

*#9998*746#
SIM File Size

*#9998*778#
SIM Service Table

*#9998*785#
RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error.

*#9998*786#
Run, Last UP, Last DOWN

*#9998*837#
Software Version

*#9998*842#
Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.

*#9998*862#
Vocoder Reg - Normal, Earphone or carkit can be selected

*#9998*872#
Diag

*#9998*947#
Reset On Fatal Error

*#9998*999#
Last/Chk

*#9998*9266#
Yann debug screen (=Debug Screens?)

*#9998*9999#
Software version

*0001*s*f*t#
Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)

*0002*?#
unknown

*0003*?#
unknown

SP-unlock SGH-600 and SGH 2100

*2767*3855#
Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.

*2767*2878#
Custom EEEPROM Reset

These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600

Universal Secret Codes Motorolla

2008-06-05T14:01:00.000-07:00

Note:
[] : (pause) means the * key held in until box appears.

Code to lock keys : Press together *7

Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []
Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []
Add messages to main menu:
[] [] [] 1 0 7 [] 1 []
Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []
Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []
Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []
Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []
Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []
Enable EFR:
[] [] [] 1 1 9 [] 1 []
Function :
[] [] [] # # # [] 1 []
Change pin:
[] [] [] 0 0 4 [] 1 []
Unblocking using the "puk" number:
[] [] [] 0 0 5 [] 1 []

There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.

You can change GSM frequencies to 900/1800 by entering the enginnering model.
Following the below steps :
enter menu and press 048263* quickly, then you will enter the secret engineering menu
under "Opcode"
input 10*0*3 for GSM 900
10*0*4 for GSM 1800
10*0*5 for GSM 1900
10*0*6 for dual band GSM 900/1800
10*0*7 for dual band GSM 850/1900

To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.

Universal Secret Codes Sony Ericsson

2008-06-05T13:56:00.000-07:00

Getting your IMEI (International Mobile Equipment Identity):
Number: *#06#

Access Software version:
> * < < * < * Reach last dialed numbers: 0 then # The Sony Ericsson Secret Menu screen: -> * <- <- * <- * Change to Default Language (English): <>

Info about SIMLOCK:
< * * <

Opening phone without a SIM card:
**04*0000*0000*0000# followed by on ‘Wrong Pin’ number

Nokia 9500 Secret Codes

2008-06-04T14:35:00.000-07:00

To check IMEI press
*#06#.

To check the Software Version press
*#170602112302#.

If Imagine the cell battery is very low, and an important call is expected what to do there is a a reserve battery in the absence of the charger then to activate the key and recharge the cell again is to press "*3370#".

#3370#
To deactivate Enhanced Full Rate Codec( EFR).

*#4720#
To activate Half Rate Codec.

*#0000#
It displays the software version of the phone.

*#9999#
To check the phones software version if *#0000# does not work.

#pw+1234567890+1#
To check the Provider Lock Status. ( "*" sigh to obtain the "p,w" and "+" symbols).

#pw+1234567890+2#
To check the Network Lock Status. ( "*" sigh to obtain the "p,w" and "+" symbols).

#pw+1234567890+3#
To check the Country Lock Status. ( "*" sigh to obtain the "p,w" and "+" symbols).

#pw+1234567890+4#
To check the SIM Card Lock Status.( "*" sigh to obtain the "p,w" and "+" symbols).

*#147#
vodafone this lets you know who called you last time *#1471#.

*#21#
Allows you to check the number that "All Calls" are diverted.

*#2640#
It displays the security code.

#30#
It lets you see the private number.

*#67705646#
It removes operator logo on 3310 & 3330.

*#73#
It reset the phone timers.

*#746025625#
It displays the SIM Clock status.

*#7760#
Manufactures code.

*#7780#
Restore factory settings.

*#92702689#
(to rember *#WAR0ANTY#)

Nokia 9300 Secret Codes

2008-06-04T14:30:00.000-07:00

NOKIA 6110 / 6120 / 6130 / 6150 / 6190 Secret Codes

2008-06-04T14:26:00.000-07:00

IMEI number:
* # 0 6 #

Software version:
* # 0 0 0 0 #

Simlock info:
* # 9 2 7 0 2 6 8 9 #

Enhanced Full Rate:
* 3 3 7 0 # [ # 3 3 7 0 # off]

Half Rate:
* 4 7 2 0 #

NOKIA 5110 / 5120 / 5130 / 5190 Secret Codes

2008-06-04T14:22:00.000-07:00

IMEI number:
* # 0 6 #

Software version:
* # 0 0 0 0 #

Simlock info:
* # 9 2 7 0 2 6 8 9 #

Enhanced Full Rate:
* 3 3 7 0 # [ # 3 3 7 0 # off]

Half Rate:
* 4 7 2 0 #

Provider lock status:
#pw+1234567890+1

Network lock status:
#pw+1234567890+2

Provider lock status:
#pw+1234567890+3

SimCard lock status:
#pw+1234567890+4

Nokia E-Series Secret Codes

2008-06-04T14:17:00.000-07:00

Check software version and the release number of your device:
*#0000#

See WLAN MAC address:
*#62209526#

See Bluetooth MAC address:
*#2820#

To hard reset and restore to factory settings:
*#7370# (default lock code is 12345)

See IMEI (International Mobile Equipment Identity) number:
*#06#

Check number where calls are diverted:
*#61#

Nokia N80 Secret Codes

2008-06-04T13:58:00.000-07:00

*#06#
To check the IMEI.

*#0000#
To check the firmware version and date.

*#92702689# *#war0anty#.
To check the IMEI. The date when it was purchased, and the date when it was repaired.

*4720# (*hra0#)
To activates th e Half Rate.

#4720# (#hra0#).
To deactivates Half Rate.

*3370# (*efr0#).
To activates Enhanced Full Rate.

#3370# (#efr0#).
To deactivates Enhanced Full Rate.

*#746085685# . (*#sim0clock#)
To check the SIM clock status.

*#7220# (*#pca0#)
To activate the GPRS and Packet Common Control Channel PCCCH) supports.

*#7230#. (*#pcd0#)
To deactivate the GPRS and Packet common control channel (PCCCH)supports.

*#7760# (*#ssn0#)
To check the manufacturing serial number.

*#2820# (*#bta0#)
To check the Bluetooth MAC address.

*#7370925538#. (*#res0wallet#)
Reset the mobile wallet.

Nokia E70 Secret Codes

2008-06-04T13:54:00.000-07:00

To check the IMEI(International Mobile Equipment identity)
*#06#

To check the firmware version and date use
*#0000#

To check the Bluetooth MAC use
*#bta0#

To check the WLAN MAC address
*#mac0wlan#

To clear the operator logo
*#opr0logo#

To activate
*#pca0#

to deactivate
*#pcd0# the GPRS PCCCH support

To check the SIM clock status
*#sim0clock#.

To check the software version
*#170602112302#.

To check the Warranty codes
*#war0anty#.

#pw+1234567890+n#
Display the SIM lock status:

n = 1: provider lock.
n = 2: network lock.
n = 3: country lock.
n = 4: SIM lock.

Nokia E65 Secret Codes

2008-06-04T13:51:00.000-07:00

*#06#
To check the IMEI.

*#0000#
To check the firmware version and date.

*#92702689# *#war0anty#
To check the IMEI. The date when it was purchased, and the date when it was repaired.

*4720# (*hra0#)
To activates the Half Rate.

#4720# (#hra0#)
To deactivates Half Rate.

*3370# (*efr0#)
To activates Enhanced Full Rate.

#3370# (#efr0#)
To deactivates Enhanced Full Rate.

*#746085685# (*#sim0clock#)
To check the SIM clock status.

*#7220# (*#pca0#)
To activate the GPRS and Packet Common Control Channel(PCCCH) supports.

*#7230# (*#pcd0#)
To deactivate the GPRS and Packet common control channel (PCCCH)supports.

*#7760# (*#ssn0#)
To check the manufacturing serial number.

*#2820# (*#bta0#)
To check the Bluetooth MAC address.
*#7370925538# (*#res0wallet#)
Reset the mobile wallet

Nokia E61 Secret Codes

2008-06-04T13:44:00.000-07:00

Hard Reset
Old : *#7370# or “Original Settings” dialogue
New : hold Green (send) and 3 and * whilst turning on
Lock code: 12345

Holding down # will toggle between the current profile and silent mode
Blue Function Key + Ctrl activates Bluetooth.
Blue Function Key + Chr activates IR.
Ctrl + C copies
Ctrl + X cuts
Ctrl + V pastes
Ctrl + Joystick Down functions as Page Down (goes to the next page down)
Ctrl + Joystick Up functions as Page Up (goes to the next page up)
Shift + Joystick Left or Right highlights one letter at a time.
Shift + Ctrl + Joystick Left or Right highlights one word at a time.
Ctrl + Joystick Left or Right moves the cursor from word to word.

*#0000#
Displays the phone’s firmware

*#06#
Displays IMEI

*#2820#
Displays your bluetooth address

*#62209526#
Displays WLAN adapter’s MAC address

*#92702689#
Displays the phone’s life timer

Nokia E60 Secret Codes

2008-06-04T13:31:00.000-07:00

*#06#
To check the IMEI.

*#0000#
To check the firmware version and date.

*#92702689# *#war0anty#
To check the IMEI. The date when it was purchased, and the date when it was repaired.

*4720# (*hra0#)
To activates the Half Rate.

#4720# (#hra0#)
To deactivates Half Rate.

*3370# (*efr0#)
To activates Enhanced Full Rate.

#3370# (#efr0#)
To deactivates Enhanced Full Rate.

*#746085685# (*#sim0clock#)
To check the SIM clock status.

*#7220# (*#pca0#)
To activate the GPRS and Packet Common Control Channel(PCCCH) supports.

*#7230# (*#pcd0#)
To deactivate the GPRS and Packet common control channel (PCCCH)supports.

*#7760# (*#ssn0#)
To check the manufacturing serial number.

*#2820# (*#bta0#)
To check the Bluetooth MAC address.

*#7370925538# (*#res0wallet#)
Reset the mobile wallet.